Chinese translation for "rolling direction"

轧制方向

Related Translations:

changing direction:  变向

command direction:  命令方向指定方向

cutting direction:  裁断方向切削方向

alternating direction:  交替方向

direction method:  方向法方向观测法投影方向方式

watch direction:  观看方位监视指定方向里面有8个方位

direction float:  定向浮子

wrong direction:  相反的方向

disguised direction:  伪装的击球方法

direction arm:  方向导杆

Example Sentences:

	1.	Iron and steel . profiled plates in rolling direction 钢铁.沿轧制方向成型的钢板
	2.	Click on the rolling direction of the arrow adjustments , in order to keep the ball to the opposite wall 点击滚动的箭头调整方向，要想办法把球踢到墙的对面。
	3.	And strengthening contribution of t1 phase is maximal in the rolling direction , minimal in the transverse direction , and midterm in the 45 direction , which means that contribution of t1 phase to anisotropy of alloys is contrary to that of textures 相在纵向和横向的强化贡献最大，而在45方向的强化贡献最小，即与织构的作用一致； t _ 1相的强化贡献则在纵向最小，在横向最大，在45方向较大，即与织构的作用相反。
	4.	Zircaloy - 4 sheet , which was cold - worked followed by recrystallization annealing , exhibits longer lcf life in the rolling direction than that in the transverse direction , and the fact that difference in lcf life between both directions becomes larger as the range of plastic strain becomes lower can be attributed to the texture effect , p - solution treatment deteriorates the alloy ' s lcf property because the treatment lowers the average value of alloy ' s schmid factors , and the subsequent annealing - treatment in a - phase range has a impact on the lcf properties , i . e . the subsequent annealing - treatment at 500 ? for 1 . 5h results in better property than that at 750 for 1 . 5h , which comes mainly from the fact that the alloy annealled at 500 for 1 . 5h has lower amount of the precipitate particles than the alloy annealled at 750 for 1 . 5h 对于冷加工后经再结晶退火处理的zr - 4合金，轧制方向的低周疲劳寿命比横向要大。随着_ p的降低，两个方向的低周疲劳寿命的差别相应增加，这是由于合金中存在织构的缘故。冷加工后经再结晶退火处理的zr - 4合金在固溶处理后，抗疲劳性能明显降低，这主要是由于固溶处理降低了合金的schmid因子；固溶处理后在相区的退火对疲劳性能有影响，即500 1 . 5h退火的抗疲劳性能要优于750 1 . 5h退火，这主要与500 1 . 5h退火的合金中沉淀相粒子的数量较少有关。
	5.	While cyclic deformation experiment under constant strain control is performed in 400 , the material shows the continuous hardening until cyclic invalidation . ( 3 ) back stress attained by kwl " s method is used to analyse the bauschinger effect during an incremental step cyclic test and cyclic deformation test under constant strain control , it is shown that back stress increases with increasing plastic strain and the numbers of cycle , and the back stress is uniform , regardless of tension or compression conditions . ( 4 ) as far as recrystallized zircaloy - 4 plate is concerned , the back stress in transverse direction is higher than that in rolling direction due to the higher schmid factor in rolling direction 对于再结晶状态的zr一4合金板材试样来说， t方向(横向)试样的背应力要高于r方向(轧制方向)的背应力，原因在于r方向的schmid因子高于t方向的schmid因子; 400下， zr一4合金的背应力要明显低于室温下的背应力;含氢200pg / g的zr一4合金的背应力大小与无渗氢的zr一4合金背应力相比，无明显区别;固溶处理后， zr一4合金的背应力大小发生了变化，在较高塑性应变下，背应力均高于固溶处理前的背应力。

Similar Words：

"rolling diaphragm actuator" Chinese translation, "rolling diaphragm principle" Chinese translation, "rolling die" Chinese translation, "rolling dig" Chinese translation, "rolling dig to the side" Chinese translation, "rolling direction of hump" Chinese translation, "rolling disc planimeter" Chinese translation, "rolling disk deck" Chinese translation, "rolling donkey" Chinese translation, "rolling door" Chinese translation